The workshop is my happy place — I go there to create. One of my favorite things to do out in my woodworking shop is to build cabinets, organizers and jigs to make it easier to work or accomplish a given task. I’ve been applying that to my recent work with 3D printing and electronics hardware hacking.
By training I am a software engineer and a preservation carpenter — yep the is an unusual mix to some — but to me I use the same part of my brain to envision a large software application and break it down into manageable pieces of code and then write them that I use to envision a chair and break it down into all the steps and pieces that start at a tree and result in a chair.
After getting some more work time at the Maker Workbench that I recently completed I realized that my hand tool storage was lacking.
I was storing my pliers, strippers, nippers and similar tools in the holes on the sides of the metal racks that support my workbench.
It seemed like a great idea — I can see the tools, they are off the workbench and reasonably accessible, but for common operations I felt I was wasting too much time and energy getting them in and out of those holes — as sometimes they would catch a bit on the way out.
After thinking about some of the optimizations I made out in my woodworking shop and watching videos like some of Adam Savage’s shop tours, behind the scenes and shop projects builds from tested.com and this video in particular which made the case for not using drawers I wanted to come up with something efficient to organize the tools I used most often on the bench.
The idea bounced around in my subconscious for a few weeks until I finally came up with the following tool rack for my pliers and similar tools:
How I built the tool rack:
The rack is about 6″ tall, the base is about 6″ wide and the rods are about 12″ long. I bought a 36″ long piece of O1 Tool Steel Round Rod, Polished Finish, Precision Ground, Annealed, Metric 10mm from Amazon here. I cut the rod on my abrasive cutoff saw and ground off any burs and chamfered the cut ends a bit so I would be sure they’d seat nicely in the 3D printed ends.
I then made what I felt was a reasonable sized 10mm end cap in SketchUp and printed it out. It was a tiny bit tight so I measured the rod and the print and adjusted things a bit and tried printing at 102, 105 and 108%. 105% was the sweet spot and gave me a nice tight fit. I also made a variant of the end cap to include a #4-40 machine screw to see if that would keep the cap on there even tighter but felt it was negligibly better in this case and recommend you print 1 or more of these caps to dial in your printer an get a real nice fit. If you still find the cap is loose you can epoxy it into place.
With the printer dialed in and the cap in hand it was time to print the sides. Rather than waste material and to increase the aesthetics of the rack I added a series of holes to the model to give it a more pleasing and modern look.
I printed the sides one at a time with a brim to try and minimize any warping.
The cleanup was easy with an X-acto knife and the assembly was simply inserting the rods into the printed end pieces and start using the rack.
The above described rod is a bit on the expensive side, costing about $15 but the ground and polished look is what I wanted and it adds a pretty good amount of weight to the tool rack and I’ve found it stays right where I leave it on the bench. It works well with all the small and medium size pliers shown below and can also accommodate some of my larger and specialty channel-locks and similar hand tools. If you are on a budget, simple mild steel rod from a hardware store or even a wooden dowel can be used.
I’ve shared out the plans and SketchUp files for the end caps and rack sides (both solid sides and the sides with the circular holes) up on Thingiverse.com here.
If you make or remix this project, please share some pics or notes in the comments below.
It can be tough working on a maker project if you don’t have a good space to work. Many times my electronics work surface was an ESD mat on the dining room table, but as my projects grew and my family grew I was under increasing pressure to find somewhere else to work. (Really it was the 3D printer that put my wife over the edge — rightfully so). I also didn’t want to have my electronics out in the garage which is my woodworking shop and full of saw dust.
The task of finding a decent place to work on electronics was more of a challenge than I expected. Lots of folks who left the dining room table seem to work on card tables or random repurposed Ikea tables and benches or purchase very expensive commercial electronics benches that are out of the range of most folks working part time as a maker. I knew there must be something in the middle that could be a reasonable solution and a reasonable bench.
As I was reading my copy of “Practical Electronics For Inventors: 4th Edition” by Paul Scherz and Simon Monk there was a brief mention of a DIY Maker Workbench that caught my eye. If you have the book it is on pages 632-633, but be careful as you might miss it buried deep in the bowels of this tome, with just a brief description and a couple of diagrams but no photos of it in use.
I wanted to rectify that problem and document how I built mine as I had to make some modifications and additions that I thought others might be interested in.
Since the the book above was written the 18″ deep metal frame that was the basis of the bench is no longer available through Home Depot and the company that made it seems to have been swallowed up by another company, but they still make and stock a 24″ deep version. I’ve compiled a hardware list below that includes all the materials I used along with links for anything that was not a simple commodity item. With the instructions from the book and my additions below I’m sure you can build yourself a great electronics/maker workbench.
Other highlights of the bench and my modifications are:
Full Spectrum LED Work Utility Light (Uses very little power and is dimmable. Leaves more power available on this circuit for my electronics)
Custom built work top with Formica surface and hard maple edging
Electrical: Wire stripper(s), Romex Jacket Slitter or Utility Knife, Wire Cutters, Pliers, Phillips and Slotted Screwdrivers, Electrical Receptacle Tester (~$5-10 and worth it)
Woodworking Tools for Bench Top: Circular saw + guide fence OR Table Saw, Router with large flush trim bit & 1/8″ rounder bit, Biscuit Joiner + Biscuits, PVA Wood Glue (e.g. TiteBond), 1.5″ Wood Screws or Drywall Screws, Drill + basic set of bits that can also handle sheet metal, J Roller (For rolling on top of the formica as it is applied), Jig Saw or Coping Saw,
Highlight Reel from the Build:
I ripped the plywood and MDF on the table saw and cross cut it using a circular saw with a guide fence leaving it about 1″ too long on purpose. Once I screwed the layers together I was able to use the guide fence to cross cut it again to final size — by doing this I know all my layers will be perfectly lined up. Make sure to account for the edging when you figure out how big your bench will be. If you work carefully you’ll want to shoot for a bench top that is about 1/4″ narrower that the metal frame is wide. That should leave a nice 1/8″ shadow line and give you room to get it seated. Also the metal is not always welded all that great on these frames as I know mine was not 100% square and many get damaged in shipping and need to be bent back into shape.
Next up I milled some hard maple stock to be the edging for the bench slab. I carefully mitered each quarter and used a biscuit joiner and glued in biscuits to secure the edging. (By using biscuits there are no nail holes to fill in) Also note that the edging should only cover the top two layers of substrate — the MDF and first layer of plywood as the lowest layer of plywood is what keys the bench top into the center shelf of the metal frame.
I used edge clamps to secure the edging as it dried.
When screwing together the 3 layers of substrate I laid out a grid on the bottom of each layer that way my screws were spaced evenly. It also allowed me to make sure my screws would not directly overlap between layers.
When cutting the outlet holes for the back splash I laid them out evenly and then marked out where they would be. I drilled a small hole in each corner and a large one in the center with enough room to allow the blade of my jig saw to fit. I sawed out the space for each outlet looking to be about 1/16″-1/8″ larger than the outlet box. I also used a file and rasp to clean up any rough edges.
With the outlet holes in place I edged the back splash with hard maple to match the bench surface and to reinforce the MDF substrate.
I rough cut the formica a couple inches bigger in each direction for what it needs to cover using saw blade with a high number of teeth — 40-60 or a dedicated laminate blade would work. Then it was time to apply the contact cement. The MDF will generally absorb more than the formica as it is more porous. You want to apply it liberally and evenly using a brush, roller or spatula and bit of cardboard. As it dries you’ll see where you need some more as you go. When it dries to the point that it is evenly tacky — meaning your finger will stick to it a bit — it’s time to apply the Formica.
I usually put a few dowels out on the bench substrate and then get the Formica all lined up but not touching each other. Once the two tacky surfaces meet they cannot be pulled apart so you need to get this right the first time and the dowels help you to get the alignment right before committing to it. That is also why we cut the sheet larger and trim it back once secured. Start from the center and work your way out using a J-Roller applying as much force as you can muster. As you work your way out to the edge you can remove more dowels until the Formica is in place. Then keep working the J-Roller until you get rid of any/all air pockets and bubbles taking longer and longer strokes working from the center out and then end to end.
To trim the Formica I use a flush cutting router bit in a router to trim back the laminate so that it is flush with the edging. I then take a 1/8″ radius round over bit to ease all the edges with the hard maple. With the bench top complete it was time to move on to the electrical work and assembly.
For outlets make sure you get all of them with the right angle bracket as shown above and as shown here. That bracket is needed in order to secure the outlets to the back splash on the bench top and for the upper outlets to attach them to the metal frame.
I used Rustoleum Black Textured paint to paint the two outlets that will be for the light switch and its outlet since they will be visible. I also bought that can of paint to match the finish on the metal shelving/rack that is the core of this bench since mine came from HomeDepot.com and had lots of rub spots on it from shipping and that would have bothered me to see every day.
I assembled the metal shelving rack as per the instructions it came with and the height of the shelves roughly in line with what the book described. Once assembled take a chair and sit at it and make sure its at a comfortable height to do your electronics work — likely a couple inches higher than what I’d want for typing at a computer. Then lift the bench top into place — you’ll want help with this as its HEAVY and I have mine in our spare bedroom upstairs so I dread moving it sometime in the future.
I attached the backsplash to the bench top using 2″ wood screws — note I say wood screws and not drywall screws which are flimsy in comparison — drywall screws have much thinner shanks that can easily snap. I then punched out the necessary holes in the outlets and screwed them into place with 5/8″ long screws.
I used 4 shelf uprights for my bench as I felt the two called out in the book would be too flimsy especially as my shelves will be covered in books and hardware and I don’t want the shelves to droop. I measured out locations that would space the uprights equally and marked the uprights and the bench with a silver sharpie and numbered them so if I have to move this bench I can re-assemble it with the exact same pieces in the same location.
I then took a center punch (or in a pinch a nail set would do) and using a hammer I hit the location I want to drill through the metal hard in order to make a small dent. This will help the drill bit stay where I want it as I drill through the metal. I secured the shelf supports to the top, middle and bottom rails of the metal shelving. I also wanted to make sure they were evenly spaced between the outlets as the armored cable will need to work around them as we’ll see below.
I cut the cable a solid amount longer than the distance between each box so I would have plenty of 12 gauge wire to work with. I then stripped off the yellow rolex wire jacked as these wires will be fed through the BX metal cable armor and fittings.
I cut each bit of cable armor to size and test fit it with the fittings as shown above. I then fed the wire through the armor and installed each assembly into the appropriate outlet boxes and secured the nuts that hold the fittings in the outlet boxes. (see below). Note that the armored cable goes behind the shelf supports.
Use a heavy duty 12 gauge or heavier extension cord to connect your bench to the wall outlet. You’ll cut off the female end and wire it into the GFCI.
I chose to put the outlet for the LED light and switch on the back side of the bench and run the armored cable up and around the back of the bench. I secured the cabling with a bunch of black plastic zip ties. I also needed the cabling to make a 90 degree right angle to connect the backsplash wiring to the outlet switch. The above fitting made this task easy. (See parts list for proper name and model)
With the cabling in place it was time to add the shelves and start installing the receptacles.
I put each switch in front of the outlet where I wanted it to make sure things were in useful positions. On the backsplash from left to right I have: 20Amp Tamper Resistant (TR) GFCI outlet, 20Amp Decora TR Outlet, 20Amp Decora TR Outlet + 2 USB ports in the center, 20Amp Decora TR Outlet and another 20Amp Decora TR Outlet. The top left is an outlet for the overhead utility LED light fixture. Top right is a light switch which works out well as its just above where the light switch on the wall is for the room lights. I also ground the metal of the bench frame to the ground of this circuit. The LED light fixture is secured with more black plastic zip ties and the cord for it is secured in the same way.
I was careful in my wiring to make sure everything downstream of the GCFI was cabled correctly and checked the ground using a receptacle tester like this one. Once you test it with live power make sure you test the GFCI and make sure all downstream outlets are cut off by the GFCI when it is tripped.
With the circuits all working it was time to put on the faceplates for the outlets and start loading up the bench. I have my ESD mat which is grounded out to the wall outlet so we don’t have a grounding loop. I have my Lulzbot TAZ6 on the left and my ESD mat, soldering stations nd fume extractor on the right.
So far the bench has been working out well and it has been great to be able to leave a project on the bench and come back to it undisturbed.
If you build your own version of this workbench, please send me a note with some pictures or leave a comment below
P.S. Since I completed the above bench I’ve also added 2 LED monitors and I’m working on a CNC controlled gaming keyboard tray, so please stay tuned for that in an upcoming post. Please consider following this blog via one of the ‘Follow this blog’ widgets on the webpage or via my Facebook Page or Twitter Feed.
P.P.S. This blog is new so please bare with me as I add to it. If you are into woodworking I have a long running blog on my traditional woodworking and writing you can find here: RainfordRestorations.com
Got some new filament today and beyond my normal favorite test print of the herringbone gear bearing I printed off a few Maker Faire Robots. It was a fun little print and I like how they look in nGen Yellow filament.
Printed on a Lulzbot Taz 6, Standard Resolution, 20% infill. The robot with his arms down came with support material that was removed during the print cleanup.
After creating my own model and printing it the next challenge I wanted to try out was printing in to colors of filament. I don’t have a flexy dual extruder yet (though I do want one) I wanted to take a shot at designing something that would work well being printed with two colors at different layers, meaning I could pause the print, swap filaments, purge and then resume the print.
I was inspired by some of the stickers and images I’ve seen online for Reverse Engineers and decided to make a fun little sign for my maker bench.
I designed this model in SketchUp and exported it as an *.stl file. It can easily scaled to a larger size. I wanted to minimize the amount of warping and among of filament used. If you want a thicker base just scale up in the Z axis.
Printed on LulzBot Taz 6
Dark Gray and Orange nGen Filament
20% infill, Standard Resolution and Speed
Printed scaled 2.0 in X and Y axes, and at 3.0 in the Z axis. This gives me something a little bigger than a business card.
The trick was sitting there watching the print and pausing at just the right time to swap the filament. This meant finding the first layer wherein the background is complete and we are about to start printing the text which is proud of that surface. I looked at the layer view in Cura and could figure out when I wanted to do that filament swap. Worked great on the first print. At some point I want to look at hacking the GCode or similar means to automate the pause, but I wanted to do it as fast as possible so the print didn’t cool down too much as I didn’t want any unnecessary adhesion issues.
I’m very happy with how this print came out and look forward to trying this technique with other models.
Back in May I ordered a Lulzbot Taz6 about a week or so after it came out — I had been waiting and saving for one for quite a while. I got to try one at the Red Hat Tower, the corporate HQ down in Raleigh NC and was quickly hooked. (I work for Red Hat, but at their engineering HQ which is is Westford MA.) Like many makers with a new 3D printer I spent a LOT of time printing random fun things from Thingiverse and similar sites.
After getting a bunch of prints under my belt the next part of my 3D printing journey was to start designing some of my own stuff to print. My first custom design was this retro looking sign of my last name — Rainford.
I designed the model using SketchUp and extruded my name in the ‘Lobster 2’ font. I then added a base to tie all the letters together into a one piece print. I also extruded ever other letter a bit more than its neighbor so that I could preserve the serifs in 3D and create additional shadow lines.
After creating the model I used a SketchUp plugin to export the model into a *.stl file. I then loaded up Cura: Lulzbot edition to slice and print the sign.
Printer and Settings:
Lulzbot Taz 6
Dark Blue nGen Filament
No supports or brim
Z-hop set to 0.75 instead of the default profile of 0.1 (I wanted the flat spaces to be smooth — worked out this value as I’d tweak it more each time I printed one. I would up printing 4 of these, one for home, one for the workshop, one for the maker bench and one for my office at work. Apparently I can’t get enough of my name or want to get my money’s worth out of the design time it took to create this model. 😉
The lesson I learned from this was in creating some material to connect the dot over the ‘i’ to the rest of the word. The model looked great in SketchUp but that bridge didn’t show up in the print — didn’t like how some of that solid resolved internal faces I could not see in the solid view I was looking at. I eventually learned about the Cleanup^3 and Solid Inspector^2 plugins for SketchUp that helped fix that issue and I’d also inspect via View->X-Ray. So the second print had a properly connected dot. I also now look at the layers view in Cura to make sure the paths, and the brim and supports when needed show up the way I would expect.
You can find this model on the TinWhiskerz Thingiverse.com page here: http://www.thingiverse.com/thing:1693112
Welcome to the TinWhiskerz Blog. A site dedicated to my maker projects — electronics, engineering, open source software and hardware, 3D printing and social learning.
Basically all my random dabbling into the nerdy arts. It’s going to be a fun journey. If you see something you like or have requests for something you’d like to see covered, please send me a note or leave a comment.
Electronics, Maker Projects, 3D Printing, Social Learning